The conditions of software for Windows 11

Supported OS/SW

* The following operating conditions are the results obtained by internal tests.
 Note that other problems may be occurred.
* The software other than those below does not support Windows 11.
  • Yes -> Functions normally.
  • Yes* -> Operable, but partially has problems.
  • No -> Cannot be used.
Product name Ver Status Workaround Plan to support
Mimaki Driver
4.x
5.x
[New installation on Windows 11]
It operates normally.tion is currently under investigation.
-
Complete
[Upgrade the OS to Windows 11 in the state you have already installed the software.]
The printer may show an error when the printer and the computer is connected with USB cable at the timing of upgrading from Windows 10.
When the printer shows the error, reboot the main power switch of the printer.
Complete
Simple Cut
-

Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
FineCut/Coat9 for Illustrator
2.2

It operates normally. [1] Camera for Gravotech laser is not supported.
-
Complete
FineCut/Coat9 for CorelDRAW
2.2

It operates normally.
[1] Camera for Gravotech laser is not supported.
-
Complete
RasterLinkTools for Illustrator
1.11.0

It operates normally.
-
Complete
RasterLinkTools for CorelDRAW
1.11.0

It operates normally.
-
Complete
Simple POP
-

Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
RasterLink7
2.3.0
It operates normally.
[1] When using Windows 10 or earlier, or macOS as a client computer, printer driver output is not available.
Please refer to “Network Connection Guide” for the OS of the client PC.
[1] Please output with hot folder when using Windows 10 or earlier OS or macOS as a client.
Complete
RasterLink6Plus
2.13.1
It operates normally.
[1] When using Windows 10 or earlier, or macOS as a client computer, printer driver output is not available.
Please refer to “Network Connection Guide” for the OS of the client PC.
[1] Please output with hot folder when using Windows 10 or earlier OS or macOS as a client.
Complete
RasterLinkPro5
4.80
It operates normally.
[1] When using Windows 10 or earlier, or macOS as a client computer, printer driver output is not available.
Please refer to “Network Connection Guide” for the OS of the client PC.
[1] Please output with hot folder when using Windows 10 or earlier OS or macOS as a client.
Complete
When using Windows 11 for RasterLink7 client
2.3.0
It operates normally.
-
Complete
When using Windows 11 for RasterLink6Plus client
2.13.1
It operates normally.
-

Complete
When using Windows 11 for RasterLinkPro5 client
4.80
It operates normally.
-
Complete
TxLink4
4.1.3
It operates normally.
-
Complete
TxLink3
3.1.11
It operates normally.
-
Complete
Printer Driver
-
Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
MigrationTool
1.2.0
It operates normally.
-
Complete
CalibrationTool
1.1.0
It operates normally.
-
Complete
SimpleStudio
-
Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
ArtiosCAD
-
Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
Mimaki 3D Link
-
Operation is currently under investigation. Do not use Windows 11 until the investigation is completed.
TBD
Mimaki Profile Master3
2.3
It operates normally.
-
Complete
JigLink
1.0.0
It operates normally.
-
Complete
CuttingLink
1.1.6
It operates normally.
-
Complete
Mimaki Profile MasterⅡ
-
-
-
Not supported
Mimaki Target Color Emulator
-
-
-
Not supported
FineCut8 for Illustrator
-
-
-
Not supported
FineCut8 for CorelDRAW
-
-
-
Not supported
RasterLink6
-
-
-
Not supported
RasterLinkPro4
-
-
-
Not supported
RasterLinkProⅢ
-
-
-
Not supported
When using Windows 11 for RasterLink6 client
-
-
-
Not supported
When using Windows 11 for RasterLinkPro4 client
-
-
-
Not supported
When using Windows 11 for RasterLinkProIII client
-
-
-
Not supported

Return to Content

PAGETOP